Hi, im new to the forum and i have some problem with my Dodge Nitro 2007 very good car atleast for me had it since 2007 never had a problen till now. If anybody can help it will be great. My problem is as follows the car goes crazy turns almost every signal on, the RPM's goes crazy up and down it selects all the gears Parking drive reverse etc.and it stalls eveytime i turn it on basically it has a big electrical problem. I already changed the computer and it still has the same problem leaving me to think is the tipm which i see that alot of people has problem with does anybody have a clue to what this problem is thanks anything helps.
Welcome to the Nitro Z family yo1andy. Have you tried resetting the computer by disconnecting the negative battery cable for 10 minutes. I'd start there first . Aslo check your fuses too.
Thanks I dont think restarting will be the problem since like i said i changed the computer and placed a new one programed. And the fuses havent checked that part but on my search i see that the tipm could be the problem since it controls almost all electrical am thinking on changing but would like first opinions or someone that has experience with this problem before i waste more noney and buying a part that is not gonna fix the problem.
Thats the only thing that im with a doubt since everyone that has issues with the tipm the problems happens to be the alarm door locks headlights and i have no problem with that just my signals on the board go off all of them rpms go crazy sometimes i can go over 40 it wont change gear it practically goes crazy
Yeah its working the same as the old one the car its working the same my mechanic was the one that put it in. The ecm came programed for my car and he tryed to figure out what the problem was but couldnt find it
You know what i wasnt gonna go but now that i have a doubt that it may not be the TIPM i think its better to go to the dealer and see what could be the problem like that i wont waste more money and keep guessing thanks for the help when i know what the issue is i will keep this post inform.
When you have a chance, head over to the Newbie Section and say "Hi".
Tell us a little about yourself and your ride.
That way we can welcome you all proper like.
TIPM or ground would be my guess as well.
But, do you get a "No Bus" message in the cluster when this happens?
Thanks Scar0 no i dont get a "No Bus" messasge just all the signals light up oil, abs, check engine, battery all type of signals rpms go crazy and usually all this happens after the car warms up i could try and change the TIPM do to most of the problems I see through my search is the TIPM worst case its not the TIPM i can return it and then I guess ill end up at the dealer.
Check the PCM plugs are tight and locked in.
Also go to an auto parts store and see if they can get any codes.
It kinda sounds like the self test. HOW-TO: Check your Nitro for sensor bugs. It dances too!
Make sure the trip select/reset knob is not stuck.
it could be your battery which is faulty , also there is a large positive lead from the battery going to the TIPM check that this is clean and tight, underneath the TIPM there is a main ground point check that this is clean and tight. also underneath the TIPM where all the connectors plug in, there is a metal frame which holds the TIPM, it is possible part of the wiring harness has rubbed against the metal causing a short circuit, or maybe there is a bad connection on one of the connectors caused by moisture and dirt, the TIPM is not waterproof at all.
if you have to part with some money to fix the Nitro, then my advice would be do this with the Dodge dealer.
When I had to move my TIPM out of the way to install my stuts I found that the tech that did my wiper recall never wire tided any of the harnesses back and all the wires were just puched under the TIPM . The edge Nitrogen is speaking of had insulation tape on it , but I even built that up with gorilla tape just to make sure wires don't rub through.
Wooow yeap thats what mostly everyone has problem with when it come to the TIPM but i dont have nothing with the alarm or the windshield wipers. My problems consist of all the alarms in the dash board and i would say the gears everything goes crazy
Communication Error - If the cluster fails to receive a selected gear message from the PCM within three seconds, the instrument cluster will display all gear selector positions until a valid selected gear message is received or until the ignition switch is turned to the OFF position.
This would indicate a problem with the CAN (Computer) network.
I'm new to this but I'm having the same problem with my 2007 Dodge Nitro reverse parking neutral and drive be flickering in the dashboard even when I'm in drive it pops up with all four box lit up and I'm trying to figure it out at this point I'm really considering getting rid of it.
Welcome to the forum @Adam Cole Bay Bay. When you have a chance, head over to the Newbie Section (<click this) and say "Hi".
Tell us a little about yourself and your ride.
That way we can welcome you all proper like.
I have a similar problem with my front signal passenger side only. YesI have already changed a light bulb socket and terminal also, reset the computer so any suggestions
Thanks
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
Dodge Nitro Forum
307.7K posts
20.9K members
Since 2006
A forum community dedicated to Dodge Nitro owners and enthusiasts. Come join the discussion about performance, modifications, suspension, reviews, troubleshooting, maintenance, and more!